Ask C200 Betriebsanweisung

C200simply designed to be sharedUser’s GuideInFocus Corporation27700B SW Parkway Avenue Wilsonville, Oregon 97070-92151-800-294-6400 •503-685-8888Fax:

9Displaying a computer image Remove the lens cap.Press the Power button on the top of the projector or the remote.The LED flashes green and the fans s

10First-time projector use with Windows 98The first time you connect a computer running Windows 98 to the projector, the computer recognizes the proje

11Skip this page if you did not connect a USB mouse cableFor Windows 98:• If you connected the USB cable, the Add New Hardware Wizard appears again. D

12Adjusting the imageAdjust the height of the projector, if necessary, by pressing the release but-ton to extend the elevator foot. Rotate the levelin

13Connecting a video device Standard video connectionsPlug the video cable’s yellow connector into the video-out connector on the video device. Plug t

14Displaying a video imageRemove the lens cap. Press the Power button on the top of the projector.The LED flashes green and the fans start to run. Whe

15Adjust the zoom or focus rings by rotating them until the desired image size and sharpness are produced.If the image is not square, adjust the keyst

16Shutting down the projectorThe projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen

17Source troubleshootingProblem Solution ResultNo startup screenPlug power cable in and remove lens cappress power buttonCorrect imageOnly startup scr

18No computer image, just the words “Signal out of range” Adjust computer refresh rate in Control Panel>Display>Settings>Advanced>Adapter

19Image fuzzy or cropped Set your computer’s display resolution to the native resolution of the projector (Start>Settings>Control Panel>Displ

20Projector troubleshootingProblem Solution ResultImage not squareAdjust keystone on keypadSquare imageEdges of image distortedTurn Overscan on in the

21Image does not fit 16:9 screenChange aspect ratio to 16:9 in Picture>Aspect ratio menuCorrect imageImage upside downTurn off Ceiling in Settings&

22Video image “torn” and fragmentedChange Video Standard in Picture>Advanced menuCorrect imageProjected colors don’t match sourceAdjust color, tint

23Lamp won’t turn on, LED blinking red (page 16)Lamp must be replaced (page 37)Lamp turns onImage not centered on screenMove projector, adjust zoom, a

24Regarding this projectorThis product is backed by a limited two-year warranty. An extended war-ranty plan may be purchased from your dealer. When se

25Using the remote controlThe remote uses two (2) provided AAA batteries. They are easily installed by sliding the cover off the remote’s back, aligni

26Using the audio To play sound from the projector, connect your source to the Audio In con-nector on the projector.To adjust the volume, use the butt

27Optimizing computer imagesAfter your computer is connected properly and the computer’s image is on the screen, you can optimize the image using the

28Optimizing video imagesAfter the video device is connected properly and the image is on the screen, you can optimize the image using the onscreen me

2EnglishDeclaration of ConformityManufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 97070 USAEuropean Office: Strawinskylaan

29Using the menusTo open the menus, press the menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are p

30Picture menuTo adjust the following five settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press

31Presets: The provided Presets optimize the projector for displaying com-puter presentations, photographs, film images, and video images. (Film input

32Advanced settingsSharpness: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.Color Space: This opt

33Settings menuAudio: allows adjustments to the sound Balance between speakers and speaker Volume. The Internal speakers and projector startup Chime c

34Screen Save: automatically blanks the screen with a black color after no sig-nals are detected for a preset number of minutes. The image returns whe

35Network: The projector has an RJ45 Ethernet connector that supports net-work connections and TCP/IP protocols. This will allow for the control and m

36MaintenanceCleaning the lens1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.Avoid using an excessive amount of cleaner, and don’t ap

37Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the lamp has been in use. After 1,980 hours, the messa

38WARNINGS: • To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.• Do not drop the lamp module. The glass

3Table of ContentsIntroduction 5Connecting a computer 7Required computer connections 7Optional computer connections 7Displaying a computer image 9

39Using the security lockThe projector has a security lock for use with a PC Guardian Cable Lock System. See “Accessories” on page 40 for ordering inf

40AppendixSpecificationsAccessoriesTemperature Operating50 to 95° F (10 to 35° C) at 0 - 10,000 feetNon-operating-4 to 158° F (-20 to 70° C) at 0 -20,

41NOTE: Use only approved accessories.Red LED Behavior and Projector ErrorsIf the projector is not functioning properly and the red LED is blinking, c

42Numerics1024x768 resolution 5AAbout 34altitude limits 40Aspect Ratio 34audio 26Audio In connector 7, 13audio volume 15Auto Image 34Auto Power 33BBla

43Llamp replacement 37lamp won’t turn on 22, 23Language 35laptopexternal video port 9LEDblinking green 16blinking red 22, 41solid green 16solid red 23

44Ttemperature limits 40Tint 15Troubleshooting 16, 17UUSB, using your mouse 7VVESA port 8Video button 14video connectionsoptional 13standard 13Video c

45Limited WarrantyInFocus Corporation (“InFocus”) warrants that the Projector (“Product”) purchasedfrom InFocus, an InFocus distributor, or an InFocus

46Limited Warranty PeriodThe Limited Warranty period commences on the date of purchase by the end-usercustomer for both the 2 year Product Warranty an

4

5IntroductionYour new digital projector is easy to connect, easy to use, easy to maintain and has XGA 1024x768 resolution. The projector comes in a ca

6Projector components and featureskeypadspeakerszoomfocus elevator foot releaseremotecontrolreceivers (IR)air intakeventcarryinghandleremotecontrolrec

7Connecting a computerRequired computer connectionsConnect the black end of the computer cable to the Computer 1 connector on the projector. Connect t

8If you prefer connecting your computer to the projector with an optional VESA cable, connect one end of the cable to the VESA port on your com-puter,